Differences Between SLIP and PPP with Dial-Up Networking |
Q148499
The information in this article applies to:
- Microsoft Windows 95
- Microsoft Plus! for Windows 95
SUMMARY
This article contains information describing technical aspects and the usage of the SLIP and PPP line-control protocols with Dial-Up Networking.
MORE INFORMATION
Microsoft's Windows 95 implementation of the SLIP and PPP protocols is based on the standards set forth by the Internet Engineering Task Force (IETF). These standards are contained in technical documents called Requests For Comments (RFC) and are widely available on the Internet. By adhering closely to these standards, connectivity to other SLIP or PPP servers similarly designed is virtually guaranteed.
Brief outlines of the protocols themselves are provided below, with information pertinent to their operation with Windows 95 following.
If more information on either protocol is required, the following RFCs are good sources of information:
RFC-1055: SLIP Implementation RFC-1661: PPP Implementation RFC-1700: Internet Assigned Numbers
The following URL contains the RFC Index, which is constantly updated, and contains links to all the RFC documents:
Serial Line Internet Protocol - SLIP
SLIP can be defined as an encapsulation method for transmitting IP packets over a serial connection. From its creation until the present time, the recommended method for implementing SLIP has remained a de facto standard.
Specifications
Packet Framing:
Special Characters
END (C0h,192d) Signals the end of a packet's transmission.
ESC (DBh,219d) Special character used when characters
duplicate the END character.
NOTE: If a data byte has the same value as the END character, a
two-byte sequence of ESC and DCh is sent instead. If a data
byte is the same as an ESC character, a two-byte sequence of ESC
and DDh is sent instead.
Packet Size:
IP (headers and data) + transport protocol headers - framing characters <= 1006 bytes
Other Information
SLIP does not have the ability to transmit more than one network protocol at a time. Its architecture does not provide a method of differentiating between network protocols. TCP/IP is the protocol that is typically used with SLIP, which made it ideal for connecting a remote computer to the Internet using a dial-up SLIP server. However, because TCP/IP is the only network protocol SLIP can carry makes it of limited use in other applications.
SLIP also provides no mechanisms for error correction. It relies on the hardware used to make the connection, and the error-correction capabilities of TCP/IP to determine if a packet's information is bad and needs to be resent.
There are no compression algorithms built into SLIP. There are variants of SLIP (for example, CSLIP, or Compressed SLIP) that provide some degree of streamlining, but the majority of SLIP connections do not use compression.
Point to Point Protocol - PPP
PPP can be defined as an encapsulation method for transmitting multiple- protocol datagrams over point-to-point links. It is more robust and versatile than its predecessor, SLIP. PPP provides a data-link layer, the Link Control Protocol (LCP), for setting up, configuring, and monitoring the connection to ensure that the connection remains reliable. In addition, by using Network Control Protocols (NCPs), different network- layer protocols can be used dynamically.
Specifications
Packet Framing:
Protocol Field (xxxxxxxx,yyyyyyyy)
The Protocol field is one or two octets, and its value
identifies the datagram encapsulated in the Information field
of the packet. The field is transmitted and received most-
significant-octet first.
Information Field (0 - n[xxxxxxxx])
The Information field is zero or more octets. The Information
field contains the datagram for the protocol specified in the
Protocol field. The maximum length for the Information field,
including padding, but not including the Protocol field, is
termed the Maximum Receive Unit (MRU), which defaults to 1500
octets. By negotiation, consenting PPP implementations may
use other values for the MRU.
Padding (0 - n[xxxxxxxx])
On transmission, the Information field may be padded with an
arbitrary number of octets up to the MRU. It is the
responsibility of each protocol to distinguish padding octets
from real information.
Link Negotiation:
Phase I
Each side exchanges LCP packets that test the integrity of
the link and configure the operational parameters the
connection will use at the data-link layer.
Phase II
Each side negotiates for and participates in user
authentication. This phase is only a suggestion to the
standard implementation of a point-to-point protocol, and as
such, may not be included in all implementations.
Phase III
Each side negotiates for the set of NCPs that will be used. For
each different type of datagram to be exchanged (IPX, IP, and so
on), an NCP must be configured and operational. This provides the
method for transmission of network-layer information.
Other Information
The most important thing to remember about PPP is that it can support multiple network protocols simultaneously, or any individual protocol by itself. In addition, it provides error correction and compression of a very sophisticated nature. While it has more overhead and additional information, the compression and error control make PPP much faster than SLIP and far more reliable.
Using SLIP and PPP with Windows 95
Windows 95 automatically supports dialing into servers that allow PPP, RAS, or NRN (NetWare Connect) connections. SLIP support must be installed separately. If you are using the CD-ROM version of Windows 95, you can install SLIP support (along with scripting support) by following these steps:
- In Control Panel, double-click Add/Remove Programs.
- On the Windows Setup tab, click Have Disk.
In the Copy Manufacturer's Files From box, enter the following line and then click OK
<drive>:\admin\apptools\dscript
where <drive> is the CD-ROM drive containing the Windows 95 CD-ROM.
- Click OK.
- Click "SLIP and Scripting for Dial-Up Networking."
- Click Install.
After you install SLIP support, SLIP and CSLIP are available as additional server types when you specify the type of server being dialed into.
NOTE: If you do not have the CD-ROM version of Windows 95, see the following articles in the Microsoft Knowledge Base for information about obtaining SLIP support:
Q135315 CD-ROM Extras for Microsoft Windows 95 Upgrade
Q146238 Microsoft Windows 95 Service Pack 1 Admin.doc File (3 of 3)
When you are using SLIP, you are limited to the use of the TCP/IP protocol. In addition, in the Dial-Up Networking connectoid, the Enable Software Compression and Require Encrypted Password options will not be available. These restrictions are limitations of the SLIP protocol, as noted previously.
When you are using PPP, you can use the full flexibility of Dial-Up Networking. You can select NetBEUI, IPX/SPX, TCP/IP, or any combination thereof. The compression and password-encryption options are also available. However, if the dial-up server does not support either of these options, they will not be used. The use of these options is negotiated during the second phase of the PPP connection.
With the addition of Microsoft Plus! for Windows 95, a computer running Windows 95 can be used as a dial-up server. However, incoming SLIP connections are not supported, as Windows 95 is not designed to route TCP/IP packets. Incoming PPP connections using NetBEUI or IPX/SPX are supported, and offer the remote computer access to the host's resources. If the host computer is connected to a LAN, the remote computer can gain access to network resources, and even be validated by a Microsoft Windows NT or Novell NetWare server.
For information about how to obtain RFC documents, please see the following article in the Microsoft Knowledge Base:
Q185262 How to Obtain Request for Comments Documents from the Internet
Keywords : dun win95
Issue type : kbinfo
Technology : kbWin95search kbGamesSearch kbPlusSearch kbWin95 kbPlus95
Last Reviewed: December 16, 2000 |
