Microsoft KB Archive/243671

Knowledge Base

How to Enable SNARAS Tracing on SNA Server 4.0

Article ID: 243671

Article Last Modified on 10/23/2003

---

APPLIES TO

• Microsoft SNA Server 4.0
• Microsoft SNA Server 4.0 Service Pack 1
• Microsoft SNA Server 4.0 Service Pack 2
• Microsoft SNA Server 4.0 Service Pack 3

---

This article was previously published under Q243671

SUMMARY

This article describes how to enable tracing for SNA Server Remote Access Service.

MORE INFORMATION

The SNA Server 4.0 compact disc contains enhanced versions of the Snaras.dll and Rassna.dll files that include the capability to write important internal process information to a file for troubleshooting purposes. To enable SNARAS tracing, use the following steps:

On the Server

1. Locate the Trcsna.dll and Trcras.dll files on the SNA Server 4.0 compact disc corresponding to the type of system SNA Server is installed on.
   
   For DEC Alpha processors:

   Alpha\System\RASSNA\Trcras.dll
   Alpha\System\RASSNA\RAS\Trcsna.dll

   For Intel-based processors:

   I386\System\RASSNA\Trcras.dll
   I386\System\RASSNA\RAS\Trcsna.dll

2. Copy the Trcsna.dll and Trcras.dll files to the %SNARoot%\System directory.
3. In the %SNARoot%\System directory, rename Snaras.dll to Oldras.dll, and Rassna.dll to Oldsna.dll.
4. In the same folder, rename the trace versions of the SNARAS DLL files from Trcsna.dll to Rassna.dll, and Trcras.dll to Snaras.dll.
5. Click Start, click Shutdown, and then restart the computer to enable the traces.
   
   The trace files will be logged in the %WinntRoot%\System32 directory as Snaras.trc and Rassna.trc.
6. When the tracing is complete, turn off the traces by renaming the Snaras.dll to Trcras.dll and Rassna.dll to Trcsna.dll. Restore the original files by renaming Oldras.dll to Snaras.dll, and Oldsna.dll to Rassna.dll.
7. Click Start, click Shutdown, and then restart the computer to restore the system to its original state.

On the Client

1. Locate the Trcsna.dll and Trcras.dll files on the SNA Server 4.0 compact disc corresponding to the type of system SNA Server is installed on.
   
   For DEC Alpha processors:

   CLIENTS\WINNT\Alpha\System\RASSNA\Trcras.dll
   CLIENTS\WINNT\Alpha\System\RASSNA\RAS\Trcsna.dll

   For Intel-based processors:

   CLIENTS\WINNT\I386\System\RASSNA\Trcras.dll
   CLIENTS\WINNT\I386\System\RASSNA\RAS\Trcsna.dll

2. Copy the Trcsna.dll and Trcras.dll files to the %SNARoot%\System directory.
3. In the %SNARoot%\System directory, rename Snaras.dll to Oldras.dll, and Rassna.dll to Oldsna.dll.
4. In the same folder, rename the trace versions of the SNARAS DLL files from Trcsna.dll to Rassna.dll, and Trcras.dll to Snaras.dll.
5. Click Start, click Shutdown, and then restart the computer to enable the traces.
   
   The trace files will be logged in the %WinntRoot%\System32 directory as Snaras.trc and Rassna.trc.
6. When the tracing is complete, turn off the traces by renaming the Snaras.dll to Trcras.dll and Rassna.dll to Trcsna.dll. Restore the original files by renaming Oldras.dll to Snaras.dll, and Oldsna.dll to Rassna.dll.

REFERENCES

For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

243784 SNARAS Traces Continually Grow In Size If Left Enabled

Keywords: KB243671

---

Send feedback to Microsoft

© Microsoft Corporation. All rights reserved.