Microsoft KB Archive/208237

Knowledge Base

Troubleshooting a Large Number of Event ID 5711 Entries Recorded on the PDC

Article ID: 208237

Article Last Modified on 11/1/2006

---

APPLIES TO

• Microsoft Windows NT Server 4.0 Standard Edition

---

This article was previously published under Q208237

SUMMARY

Event ID 5711 (Successful partial domain synchronization) is an informational event, you generally see on the PDC. This event indicates that a successful synchronization event has occured with a BDC.

MORE INFORMATION

If you observe these event IDs on the PDC, it is not an issue unless synchronization is happening too often. There are several causes for a large numbers of Event ID 5711's recorded in the event log of the PDC, and this could indicate an issue. This article is designed to help determine the cause of the large number of events.

1. Check to see if any built-in accounts have been modified. For example:
   
   • The administrator for the domain has been removed from the Administrators group on the domain controller.
   • The Administrator's account is made a non-Administrator account.
   • The Administrator's account is disabled using the Disable account check box.
   • The Administrator's account is configured to expire.
   • The Domain Admins global group is removed from the Administrators local group.
   • The administrator is removed from the Domain Admins global group.

   
   For additional information about Event ID 5711, click the article number below to view the article in the Microsoft Knowledge Base:

   161569 Event ID 5711 Fills Event Log on Primary Domain Controller

2. Check for an account lockout. Account lockout can cause immediate synchronization and a large number of event ID 5711 messages. You can detect account lockouts using the following tools:
   
   • Checked version of Netlogon.dll
   • Event Viewer
   • Network Monitor
   • User Manager for Domains
3. Install the checked version of Netlogon.dll. If you use the correct debug flag configuration (0x29b6ffff), you can observe what gets written to the Changelog file. You can use the log file to help determine the cause of the large number of 5711 events.
   For additional information about account lockouts, click the article number below to view the article in the Microsoft Knowledge Base:

   189541 Using the Checked Netlogon.dll to Track Account Lockouts

4. You can also install the debug version of Netlogon and run some tests to balance processor utilization and network utilization for database synchronization. Using the correct debug flag configuration (0x29b6ffff), you can observe what gets written to the Changelog and measure the start and end times for SAM database synchronization.
   
   For testing purposes generate 1, 10, 50, 100, or 500 changes then measure [(End time - Start time) / # of changes] to understand the number of changes that can be replicated.

There are a few domain tuning issues that can have an effect on the number of 5711 events. For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

238191 Partial Replication May Take a Long Time with Very Large Groups

If you install the Service Pack 4 version of the Netlogon.dll file, the secure channels for BDCs are not dropped when there are more than 250 machine accounts. For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

154398 BDC Secure Channel May Fail if More Than 250 Computer Accounts

You can install Service Pack 4, which installs a new version of the Samsrv.dll file on the PDC to avoid immediate SAM syncronization for machine account password changes. For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

154502 Replication Increased by ANNOUNCE_IMMEDIATE

For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

175468 Effects of Machine Account Replication on a Domain

If you are running Service Pack 4, investigate disabling or increasing the machine account password change policy. There are three ways to resolve machine account replications.

• Add the following registry parameter on all Windows NT workstations:
  

     Key     = HLM\SYSTEM\CurrentControlSet\Services\NetLogon\Parameters
     Value   = DisablePasswordChange REG_DWORD 1
     Default = 0
                          

  NOTE: This registry key prevents you from changing passwords on workstations. You could add this registry value after having joined the domain and restarted the computer, so that the computer account password would have at least been changed once with a random value only known by the computer.

• Refuse passwords changed at domain controllers levels. On all domain controllers, add the following registry value:

     Key     = HLM\SYSTEM\CurrentControlSet\Services\NetLogon\Parameters
     Value   = RefusePasswordChange REG_DWORD 1
     Default = 0
                          

  For additional information, click the article number below to view the article in the Microsoft Knowledge Base:

  154501 How to Disable Automatic Machine Account Password Changes

• A new parameter has been added as a hotfix in order to change the frequency at which workstations change secure channel password. You can add it to all workstations and also on all BDCs. (This hotfix is the Service Pack 4 version of the Samsrv.dll file.)

     Key     = HLM\SYSTEM\CurrentControlSet\Services\NetLogon\Parameters
     Value   = MaximumPasswordAge REG_DWORD
     Default = 7
     Range   = 1 to 1,000,000 (in days)
                          

Keywords: kbenv kberrmsg kbinfo KB208237

---

Send feedback to Microsoft

© Microsoft Corporation. All rights reserved.