Article ID: 147951
Article Last Modified on 12/8/2003
APPLIES TO
- Microsoft SNA Server 2.0, when used with:
- Microsoft Windows NT 4.0
- Microsoft SNA Server 2.1, when used with:
- Microsoft Windows NT 4.0
- Microsoft SNA Server 3.0, when used with:
- Microsoft Windows NT 4.0
- Microsoft SNA Server 2.11 Service Pack 1, when used with:
- Microsoft Windows NT 4.0
- Microsoft SNA Server 3.0 Service Pack 4, when used with:
- Microsoft Windows NT 4.0
This article was previously published under Q147951
SUMMARY
This article includes a table that represents all possible SNA Server combinations of client types and platforms. If there is a choice of a client type to use, it is recommended that you use the SNA Server client for the platform. For example, in Windows NT, use the SNA Server client for Windows NT.
SNA Server Client types
Platform MS-DOS OS/2 Windows 3.x Windows NT Windows 95
--------------------------------------------------------------
MS-DOS X N N N N
OS/2 M X N N N
Windows 3.x X1 N X N N
Windows NT X2 N X3 X X
Windows 95 M N X4 N X
Clients for UNIX and Macintosh are provided by third party software developers, and are supported in the platforms designated by the client's vendor.
The following lists and describes the different marks used in the table above:
Marks Description
----- -----------
X<#> Represents the client type that is compatible with the associated
platform. <#> is mentioned below.
N Not applicable or not supported.
M<#> May work, but has not been tested. <#> is mentioned below.
<#> Description
--- -----------
1 MS-DOS SNA Server Client on Windows 3.x platform (for use with
IBM PC Support). For additional information, please see the
following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q107193
TITLE : Running IBM PC Support/400 on SNA Server
2 MS-DOS SNA Server Client on Windows NT platform (for use with IBM
PC Support). For additional information, please see the following
article in the Microsoft Knowledge Base:
ARTICLE-ID: Q103684
TITLE : IBM PC Support/400 and Windows NT
3 Windows 3.x SNA Server Client on Windows NT platform. The Windows
3.x SNA Server client must be used on a Windows NT computer
(where a 16-bit 3270/FMI application runs). The Windows NT SNA
Server client provides a thunking layer for all other SNA Server
API's. There are special instructions for the installation of the
Windows SNA Server 3.x client in Windows NT (where the actual SNA
Server is running on the system:
- Start the Windows SNA Server 3.x client setup on the SNA
Server.
- In the "Client/Server Protocols" dialog box, select the
TCP/IP. NOTE: If you have SNA Server 2.11 SP1, select Novell
Netware.
- In the "SNA Server Location" dialog box, select the Remote.
Enter the IP address or computer name of the SNA Server that
the Windows 3.x client is being installed. In other words, the
remote destination is pointing to itself. If you select Novell
Netware, then enter the SNA Server domain name and add the
following entries to the [wnap] section in WIN.INI:
[wnap]
Remote=<domainname>
NosType=NETWARE
In this configuration, both 32-bit and 16-bit 3270/FMI
applications can work on the same computer).
4 Windows 3.x SNA Server Client on Windows 95 platform. The
Windows 3.x SNA Server client must be used in Windows 95 if
you want to run any 16-bit SNA Server aware application. No
thunking is provided for any SNA Server API on the Windows 95
SNA Server client. To use the Windows 95 SNA Server client, a
32-bit application must be used.
Additional query words: prodsna sp1 unix mac macintosh parker
Keywords: kbinfo kbnetwork KB147951
