Calculating Memory Requirements for MS-DOS-Based Apps |
Q43041
The information in this article applies to:
- Microsoft Windows Software Development Kit (SDK) versions 3.0, 3.1
SUMMARY
It is extremely difficult for an application to determine in advance how much memory an MS-DOS (non-Windows) application will require to run. This data can be estimated under real and standard modes; however, there is no method to determine this information in enhanced mode.
MORE INFORMATION
The Windows module WinOldAp is required to run MS-DOS-based applications. One complication is that once WinOldAp is in memory, it can run many applications. In the following table, "PIF Req'd" indicates the amount of memory required for the application as listed in the corresponding PIF file and "PIF Des'd" indicates the amount of memory desired by the application as listed in the corresponding PIF file. The following table indicates the difference between applications:
PIF PIF Free Mem Free Mem Memory Req'd Des'd Before After Usage ----------------------------------------- 160 160 418 155 263 First copy run 160 160 153 152 1 Second copy run
As this table indicates, the second copy of the application costs almost no memory. This is because the two copies of the application share the same memory and are swapped in and out of memory (to disk, to a RAM drive, or to expanded memory, depending on the WIN.INI settings).
Another factor is the order in which MS-DOS-based applications are loaded. The statistics below demonstrate these differences. In the first case, an 80K program is loaded followed by a 160K program. In the second case, the 160K program is loaded followed by the 80K program: Case 1:
PIF PIF Free Mem Free Mem Memory
Req'd Des'd Before After Usage
-----------------------------------------
80 80 418 244 174 App #1 runs first
160 160 244 37 207 App #2 runs second
381 Total memory usage
Case 2:
PIF PIF Free Mem Free Mem Memory
Req'd Des'd Before After Usage
----------------------------------------
160 160 418 154 264 App #2 runs first
80 80 154 153 1 App #1 runs second
265 Total memory usage
These results are not as unusual as they may appear. In the second case, the larger application (App #2) is loaded first. This sets the WinOldAp swapping partition large enough to hold the application. When the smaller application (App #1) is run, it fits into the existing partition. In contrast, in the first case, the smaller application is run first, therefore the swapping area is not set large enough to hold the larger application. When the larger application is loaded, WinOldAp must create a completely separate partition to hold it.
The amount of memory needed to run an old application varies, depending on the following:
- Whether or not WinOldAp is loaded
- Whether the existing swap area (if any) is large enough to hold it
- Whether the application screen is saved in text or graphics mode
- Whether large-frame, small-frame, or no EMS is in use (this variable does not apply to Windows version 3.1)
- The contents of the Memory Required and Memory Desired fields in the PIF file
- Other factors related to the inner workings of the Windows memory manager and the WinOldAp module
These methods are not applicable to enhanced mode Windows. The only way to determine if an MS-DOS-based application will run under enhanced mode is to attempt to run the application and see if the attempt succeeds. Even this information is not available to another application because the WinExec return value only indicates that WinOldAp has been successfully loaded into memory. This value does not contain any information regarding the real target application.
The handling of this type of problem is addressed by Windows version 3.1. In Windows version 3.1, the TOOLHELP library can be used to retrieve the Exit Code of a Windows-based application. This also works in Windows version 3.0, however, the problem is that WINOLDAP (the MS-DOS-based application's Windows agent) for Windows version 3.0 always exits with exit code 0. Therefore, there is no way to obtain results of the attempted MS-DOS-based application run. The version of WINOLDAP included with Windows version 3.1 will exit with the exit code of the MS-DOS-based application that was run, or one of the following special values:
;
; Special WINOLDAP exit codes
;
EXIT_NoFile EQU 81h ; Could not start due to file or
; directory access problem
EXIT_NoMem EQU 82h ; Could not start due to insufficient
; memory
EXIT_Crash EQU 83h ; VM crashed (abnormal termination)
EXIT_BadVer EQU 84h ; Could not start due to bad version
EXIT_ExecFail EQU 85h ; Could not start because MS-DOS EXEC failed
EXIT_TaskAPIFail EQU 86h ; Could not start because task switch API
; refused start (standard mode only)
NOTE THAT THESE SPECIAL CODES MAY OVERLAP WITH AN EXIT CODE USED BY THE MS-DOS-BASED APPLICATION. If this happens, there is no way to correct it other than to change the MS-DOS-based application to use different exit codes that do not conflict with these special ones.
ALSO NOTE: The exit code of a .BAT file run is always 0. This is a property of COMMAND.COM, which is part of MS-DOS.
Additional query words: no32bit 3.00 3.10
Keywords : kb16bitonly
Issue type :
Technology : kbAudDeveloper kbWin3xSearch kbSDKSearch kbWinSDKSearch kbWinSDK300 kbWinSDK310
Last Reviewed: November 6, 1999 |
