Microsoft KB Archive/102230

The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

ACC1x: Setup (STFSETUP) GP Faults in Windows Standard Mode

Q102230

The information in this article applies to:

Microsoft Access 1.1
Microsoft Access Distribution Kit, version 1.1

SYMPTOMS

When you are running Microsoft Windows in standard mode, the error message "STFSETUP caused a general protection fault in STFSETUP.EXE" will occur near the end of the installation process if you are running any of the following:

The retail Setup of Microsoft Access version 1.1.
A workstation Setup (/n) from the version 1.1 upgrade disks.
A custom application developed with the Microsoft Access Distribution Kit (ADK).

CAUSE

This problem is caused by the detection and implementation of sharing mechanisms.

RESOLUTION

Run Windows in 386 enhanced mode during Setup. You may then switch back to standard mode to run your applications.

NOTE: This problem is solely confined to the Setup process. In no way does it affect how Microsoft Access runs in either standard or 386 enhanced mode.

If for some reason you cannot run Microsoft Windows in 386 enhanced mode, modify STFSETUP.IN_ as described below. Separate procedures follow for retail, upgrade, and ADK users.

Steps for Retail Users

Make a backup copy of Disk1.

On the backup disk, use an editor to modify the STFSETUP.IN_ file. Change the [System Paths] section from

   [System Paths]
      SYSTEMPATH = "" ? DETCMD.DLL GetWindowsSysDir
      WINDOWSPATH = "" ? DETCMD.DLL GetWindowsDir
      HARDDRIVELIST  = "" ? DETCMD.DLL GetAllValidLocalHardDrives
      NETDRIVELIST = "" ? DETCMD.DLL GetAllValidNetworkDrives

   to

   [System Paths]
      SYSTEMPATH = "" ? DETCMD.DLL GetWindowsSysDir
      WINDOWSPATH = "" ? DETCMD.DLL GetWindowsDir
      HARDDRIVELIST = "" ? DETCMD.DLL GetAllValidLocalHardDrives
      NETDRIVELIST = "" ? DETCMD.DLL GetAllValidNetworkDrives
      WINDOWSMODE = "" ? DETCMD.DLL GetWindowsMode

Then change the following

    DoShareStuff = +
     set CurrentDialog = DoShareStuff
     set MAKEBAK = "NO"
     ui start VSHARERunning
     ifstr $(ANSWER) == "NO"

   to

    DoShareStuff = +
     set CurrentDialog = DoShareStuff
     set MAKEBAK = "NO"
     ifstr $(WINDOWSMODE) != "ENHANCED"
        set ANSWER = "NO"
     else
        ui start VSHARERunning
     endif
     ifstr $(ANSWER) == "NO"

Steps for Version 1.1 Upgrade Users

Single-user upgrades and Admin upgrades (setup /a) work fine. However, to run Setup or setup /n from the network with Windows in standard mode, you must first make the changes mentioned above to the STFSETUP.IN_ file in the ACCESS\INSTALL subdirectory on the network.

Steps for ADK Users

The ADK Setup works fine in Windows standard mode. However, before you create disks for your application, modify the SETUPWIZ.IN_ file (and optionally the CUST12MB.IN_, CUST14MB.IN_, and CUST720K.IN_ files) as follows:

Change the following

   [System Paths]
       SystemPath =  "" ? DETCMD.DLL GetWindowsSysDir
       WindowsPath     =  "" ? DETCMD.DLL GetWindowsDir
       HARDDRIVELIST   = "" ? DETCMD.DLL GetAllValidLocalHardDrives
       NETDRIVELIST = "" ? DETCMD.DLL GetAllValidNetworkDrives

   to

   [System Paths]
       SystemPath =  "" ? DETCMD.DLL GetWindowsSysDir
       WindowsPath     =  "" ? DETCMD.DLL GetWindowsDir
       HARDDRIVELIST   = "" ? DETCMD.DLL GetAllValidLocalHardDrives
       NETDRIVELIST = "" ? DETCMD.DLL GetAllValidNetworkDrives
       WINDOWSMODE =  "" ? DETCMD.DLL GetWindowsMode

NOTE: Unlike the Microsoft Access version 1.1 corrections, the first two variables in the [System Paths] section of the ADK is case-sensitive.

Add the test case around VSHARERunning by changing the following from

    DoShareStuff = +
     set CurrentDialog = DoShareStuff
     set MAKEBAK = "NO"
     ui start VSHARERunning
     ifstr $(ANSWER) == "NO"

   to

    DoShareStuff = +
     set CurrentDialog = DoShareStuff
     set MAKEBAK = "NO"
     ifstr $(WINDOWSMODE) != "ENHANCED"
        set ANSWER = "NO"
     else
        ui start VSHARERunning
     endif
     ifstr $(ANSWER) == "NO"

NOTE: This is exactly the same change as the Microsoft Access version 1.1 change.

STATUS

Microsoft has confirmed this to be a problem in Microsoft Access version 1.1 and the Microsoft Access Distribution Kit version 1.1. This problem no longer occurs in Microsoft Access version 2.0 or the Microsoft Access Developer's Toolkit version 2.0.

MORE INFORMATION

Steps to Reproduce Problem

Start Windows in standard mode (win /s), using the Microsoft Access version 1.1 Retail disks.
Insert Disk 1 into drive A for 3.5-inch disks (or B for 5.25-inch disks).
From the File menu in Program Manager, choose Run.
Type a:\setup (or b:\setup) and press ENTER.
Follow the instructions on your screen.

When you insert the last disk, you will receive this error.

Additional query words: gpf

Keywords : kbsetup
Issue type : kbbug
Technology :