Article ID: 101177
Article Last Modified on 10/3/1999
APPLIES TO
- Microsoft Windows for Workgroups 3.1
This article was previously published under Q101177
SUMMARY
Sun Microsystems has announced that version 5.0 of its PC-NFS network operating system software supports connectivity with Microsoft Windows for Workgroups (WFWG) version 3.1. This article describes how to set up PC-NFS with Windows for Workgroups. This procedure is designed for use with PC-NFS version 5.0 only; previous versions of PC-NFS are not compatible with Windows for Workgroups. Microsoft will assist in the installation of PC-NFS with Windows for Workgroups. Sun Microsystems is responsible for supporting the installation, configuration, and use of PC-NFS. Customers who have issues that cannot be resolved with standard network troubleshooting should contact Sun Microsystems for assistance.
MORE INFORMATION
Installing WFWG and PC-NFS Version 5.0
To use PC-NFS version 5.0 with Windows for Workgroups version 3.1, you must use the updated WFWNET.DRV driver included with PC-NFS. To update the driver, simply delete the current version located in your WINDOWS\SYSTEM subdirectory, and replace it with the current version.
To install and provide connectivity to PC-NFS and Windows for Workgroups, do the following:
- Install Windows for Workgroups version 3.1.
- Run the PC-NFS Install program, and select NDIS as the network adapter.
- Run the QuickNDIS utility, and configure it for Windows for Workgroups.
- Run the Winstall program.
NOTE: For further information about installing and configuring PC-NFS, refer to your PC-NFS documentation.
The installation program for Sun PC-NFS makes changes to the AUTOEXEC.BAT, CONFIG.SYS, PROTOCOL.INI, and SYSTEM.INI files. These changes are documented in your PC-NFS installation guide.
AUTOEXEC.BAT
The following lines are added to the AUTOEXEC.BAT file, but the SET statements vary with each installation:
Set TZ=EST5EDT
Set NFSDRIVE=C
Set NFSPATH=C:\NFS
Set TN_DIR=C:\NFS\TELNET
C:\NFS\PRT *
C:\NFS\NET INIT
C:\NFS\RTM
CONFIG.SYS The following lines are added to the CONFIG.SYS file after the device drivers installed by Windows for Workgroups. The lines should appear in this order:
Device=C:\NFS-NDIS.SYS
Device=C:\NFS\PCNFS.SYS
Device=C:\NFS\SOCKDRV.SYS
PROTOCOL.INI
The following section is added to the PROTOCOL.INI file:
[NFS-NDIS]
DriverName=NFSLINK$
Bindings=MS$ELNKII
SYSTEM.INI
The following lines are added to the identified sections of the SYSTEM.INI file:
[Boot]
secondnet.drv=pcnfs.drv
[386Enh]
secondnet=pcnfs.386
WFWG and Previous Versions of PC-NFS
If you install Windows for Workgroups version 3.1 on a network running a version of PC-NFS earlier than version 5.0, Windows for Workgroups does not display a warning that this version of PC-NFS is not supported. (Normally, Windows for Workgroups issues a warning during setup if the currently installed networking software is not compatible with Windows for Workgroups.)
Windows for Workgroups version 3.1 Setup does not have the ability to detect the presence of a PC-NFS network. To run Windows for Workgroups properly on a Sun PC-NFS workstation, you must either update your PC-NFS software to version 5.0 or remove all references to PC-NFS connectivity from the CONFIG.SYS and AUTOEXEC.BAT files. If you don't remove the references to the Sun client software before rebooting, the system may stop responding (hang) as the conflicting network device drivers attempt to load.
The products included here are manufactured by Sun Microsystems, a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability.
KBCategory: kbnetwork kbdisplay kb3rdparty kbsetup
KBSubcategory: wfw wfwg
Additional query words: 3.10 3.1
Keywords: KB101177
