Windows NT 3.1 install error in VMware workstation 8
-
betascollector
- Donator
- Posts: 1071
- Joined: Tue Jul 07, 2009 4:06 am
- Location: C:\WINDOWS\System32
Re: Windows NT 3.1 install error in VMware workstation 8
Change your CD-ROM settings.
Re: Windows NT 3.1 install error in VMware workstation 8
use SCSI?betascollector wrote:Change your CD-ROM settings.
- MSFacts101
- Posts: 38
- Joined: Fri Dec 23, 2011 8:04 pm
Re: Windows NT 3.1 install error in VMware workstation 8
You need an SCSI drive as said in the Setup, and you use an IDE Drive.
Also, if you change it to SCSI, it still won't work, since it is incompatible.
The best thing you can do is to follow this guide.
In short, partition/format with MS-DOS 5 and copy files to the Virtual Hard Drive and start the setup from there, note that you must change 2 files after the second txt setup fase, otherwise you can scrap that VM and redo it.
Also, if you change it to SCSI, it still won't work, since it is incompatible.
The best thing you can do is to follow this guide.
In short, partition/format with MS-DOS 5 and copy files to the Virtual Hard Drive and start the setup from there, note that you must change 2 files after the second txt setup fase, otherwise you can scrap that VM and redo it.
~ MSFacts101.
Re: Windows NT 3.1 install error in VMware workstation 8
Thank you very much ,I install it successfully.MSFacts101 wrote:You need an SCSI drive as said in the Setup, and you use an IDE Drive.
Also, if you change it to SCSI, it still won't work, since it is incompatible.
The best thing you can do is to follow this guide.
In short, partition/format with MS-DOS 5 and copy files to the Virtual Hard Drive and start the setup from there, note that you must change 2 files after the second txt setup fase, otherwise you can scrap that VM and redo it.
- TheCollector1988
- Donator
- Posts: 3604
- Joined: Wed Feb 23, 2011 12:11 am
- Location: Italy
- Contact:
Re: Windows NT 3.1 install error in VMware workstation 8
use Virtual PC and there's an IDE CD-ROM driver for NT 3.1 floating around (bit cannot work on the setup)
- MSFacts101
- Posts: 38
- Joined: Fri Dec 23, 2011 8:04 pm
Re: Windows NT 3.1 install error in VMware workstation 8
Even if you install it in Virtual PC, it still asks for an SCSI CD-ROM and you must use the provided guide in the link.
~ MSFacts101.
- TheCollector1988
- Donator
- Posts: 3604
- Joined: Wed Feb 23, 2011 12:11 am
- Location: Italy
- Contact:
Re: Windows NT 3.1 install error in VMware workstation 8
I know, and that IDE CD-ROM driver works after the OS is installedMSFacts101 wrote:Even if you install it in Virtual PC, it still asks for an SCSI CD-ROM and you must use the provided guide in the link.
Re: Windows NT 3.1 install error in VMware workstation 8
Use IDE instead of SCSI
- TheCollector1988
- Donator
- Posts: 3604
- Joined: Wed Feb 23, 2011 12:11 am
- Location: Italy
- Contact:
Re: Windows NT 3.1 install error in VMware workstation 8
as the SCSI controller emulated by VMware is not supported by NT 3.1 and, because, it is PCI-based and the OS barely supports PCI devicesBlaBlaBla4042 wrote:Use IDE instead of SCSI
Re: Windows NT 3.1 install error in VMware workstation 8
I map the disk and copy files to the disk and install itTheCollector1988 wrote:as the SCSI controller emulated by VMware is not supported by NT 3.1 and, because, it is PCI-based and the OS barely supports PCI devicesBlaBlaBla4042 wrote:Use IDE instead of SCSI
Re: Windows NT 3.1 install error in VMware workstation 8
Because the SCSI adapter is not supported, you will have to install MS-DOS, then use the dos installation method.. You can convert it to NTFS but you will be restricted to a 2GB IDE disk for C ...
There is a PCI driver for the network card that VMWare uses some AMD PCNet type thing ( 11265315.exe ..?)
And don't forget about the CPU level in the inf files......
There is a PCI driver for the network card that VMWare uses some AMD PCNet type thing ( 11265315.exe ..?)
And don't forget about the CPU level in the inf files......
"Those who don't understand UNIX are condemned to reinvent it, poorly." – Henry Spencer
Re: Windows NT 3.1 install error in VMware workstation 8
You might as well skip that and get the latest version from AMD, http://support.amd.com/us/Embedded_Tech ... nt_350.zip. Don't bother with the installation program, it's not designed for earlier versions of NT. You can extract the binaries though and use them directly. Using the AMD PCnet drivers in the DRVLIB directory from an NT 3.5 installation works too, they're just a slightly older version. The AMD network adapter is supported in both VMWare and VirtualBox.louisw3 wrote:There is a PCI driver for the network card that VMWare uses some AMD PCNet type thing ( 11265315.exe ..?)
Re: Windows NT 3.1 install error in VMware workstation 8
Change cdrom settings Or Use other virtual machine(vpc,virtual box...)